A Snow and ski forum. SkiBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » SkiBanter forum » Skiing Newsgroups » Nordic Skiing
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

How to remove Salomon SNS Profil binding?



 
 
Thread Tools Display Modes
  #11  
Old February 10th 09, 01:50 PM posted to rec.skiing.nordic
highpeaksnordic
external usenet poster
 
Posts: 118
Default How to remove Salomon SNS Profil binding?

On Feb 9, 4:07*pm, jeff potter wrote:
I have a set of skis with the Salomon SNS Profil manual bindings
What's a good way to remove them?


You've gotten a lot of good advice already. We have a more direct
approach for the plastic cap at the tail end of the binding baseplate
- take a very small straight-blade screwdriver and stand it straight
up in the molded slot, rap sharply and drive the blade straight thru,
then pry it up. You can reuse it, we throw it out and replace w/ a
new one when the binding is remounted.

The screws are # 3 Pozi-Drive, many shops sell the screwdrivers, many
hardware stores also sell Vermont American bits for 1/4" magnetic bit
holders which we chuck into battery operated drills and yes, we always
adjust the clutch settings on them.

One thing not mentioned is what happens to the holes left over in the
ski. We always plug them w/ the proper sized plastic plug from an
assortment we have. The hole is glued, plug tapped into the ski and
lightly sanded flush w/ the topsheet. Of course, if the holes are re-
used they are glued again before sending the screws home.

- Bob
Ads
  #12  
Old February 10th 09, 02:19 PM posted to rec.skiing.nordic
jeff potter
external usenet poster
 
Posts: 191
Default How to remove Salomon SNS Profil binding?

On Feb 9, 6:43*pm, ADK Skier wrote:
On Feb 9, 4:07*pm, jeff potter wrote:



I have a set of skis with the Salomon SNS Profil manual bindings on
them. Skate model.


What's a good way to remove them?


I see what looks like a plug at the rear of the heel plate but they're
not easily removed. I can keep trying.


I've removed the rubber bumpers. The plastic "S" snap-cover in the
front-center of the binding, over the front-center screw, doesn't seem
to want to come off. Do I just work a screwdriver under the front edge
somehow?


How do I expose the 2 side-screws? I don't see how to release the
"bail" so that it can flip out of the way.


Help? Links?


Thanks, JP


Jeff,
I've removed tons of these bindings. It really doesn't take rocket
science. Most of the time I can get my Swiss Army knife to remove the
plug in the back. Hold it vertically and run it around the plug as you
work it up. I have also used a real small drill bit and drilled a hole
in it and they ride up the drill bit. The S cap in the front comes up
really easy with the edge of my Swiss Army knife. Get the blade under
it and pry up. Than I take my knife and work it from the back of the
binding plate to the front. Be careful on this move with the knife.
Just get the knife under the plate and work free the glue tape. Don't
pry up but move the knife along. This works every time. Hard to
beleive you've never taken one of these off after all the knowlege and
experience you have.


I've only installed one set of SNS Profil autos (for my wife). Never
removed them. Used NNN otherwise for decades.

I still haven't heard about how to get at the 2 side-screws. I can't
even see them. ? They appear to be hidden under the pivoting metal
shell cover---I don't see how to pivot it to expose the heads.
  #13  
Old February 10th 09, 03:18 PM posted to rec.skiing.nordic
jeff potter
external usenet poster
 
Posts: 191
Default How to remove Salomon SNS Profil binding?

PS: Ah, ha. I dug into it. Here's what's really going on with this
binding type. The white "cap" over at the rear of the heel plate is
NOT a cap at all. It's a one-use barbed-plug-rivet thingy. There is NO
screw under it. So you do not really just pry it up. You pry at it but
your efforts are pulling it out of THE SKI. It has a "barb" on the end
to prevent you from doing this. So eventually this item BREAKS OFF,
leaving its barb inside the ski. Terrible design, so it seems. How to
reinstall the binding onto another ski? YOU CANNOT. You MUST acquire
another undamaged white plug-rivet. Where? Who knows. Nonstandard
item. I suppose a local shop might have some around. It might be
outdated for all I know. These are somewhat older bindings. I can't
imagine such a method lasting more than one design cycle. Ugh.

Anyway, then you lift off the heel plate section-chunk and pull it to
the rear and off of the front part of the binding and the side screws
are exposed. Now we're back in familiar territory and I expect no
further difficulties...

--JP
  #14  
Old February 10th 09, 03:53 PM posted to rec.skiing.nordic
jeff potter
external usenet poster
 
Posts: 191
Default How to remove Salomon SNS Profil binding?

PPS: I removed the other barbed-plug out without breaking it, but it's
a bit marred and "vexed". I'm not sure I'd want to re-use it (or
resell it). They don't appear designed to be reusable. Oh well! --JP
  #15  
Old February 10th 09, 09:08 PM posted to rec.skiing.nordic
[email protected]
external usenet poster
 
Posts: 327
Default How to remove Salomon SNS Profil binding?

On Feb 10, 7:53*am, jeff potter wrote:
PPS: I removed the other barbed-plug out without breaking it, but it's
a bit marred and "vexed". I'm not sure I'd want to re-use it (or
resell it). They don't appear designed to be reusable. Oh well! --JP


Jeff,

When I install SNS bindings, I through that stupid white plug away and
put a regular screw instead. So even if the plug got damaged when you
pull it out, just repace it with a regular screw. The newer pilot
bindings abandended the plug design altogether (I wonder what the
rationale for using the stupid plug was...)
  #16  
Old February 16th 15, 05:32 AM posted to rec.skiing.nordic
[email protected]
external usenet poster
 
Posts: 3
Default How to remove Salomon SNS Profil binding?

On Monday, February 9, 2009 at 4:07:01 PM UTC-5, jeff potter wrote:
I have a set of skis with the Salomon SNS Profil manual bindings on
them. Skate model.

What's a good way to remove them?

I see what looks like a plug at the rear of the heel plate but they're
not easily removed. I can keep trying.

I've removed the rubber bumpers. The plastic "S" snap-cover in the
front-center of the binding, over the front-center screw, doesn't seem
to want to come off. Do I just work a screwdriver under the front edge
somehow?

How do I expose the 2 side-screws? I don't see how to release the
"bail" so that it can flip out of the way.

Help? Links?

Thanks, JP


This is how I removed my Saloman Profil SNS Alpine cross country ski bindings. I popped off the rear (heel) plastic white cap (3/8" diameter) with a Swiss knife blade and removed the screw below it, I used a number 2 (red) Robertson bit (Canada). Slide the white plate to the rear and off exposing the next screw, remove it and slide off the 2nd white plate to the rear exposing 2 edge (side) screws. Remove them. Next the front (black plastic cap) needs to come off to expose the final screw that holds down the binding for the toe of the boot. Press all the way down on the square release button, hold it down while inserting a flat screwdriver between the black cap and the blue plastic that houses the orange rubber toe bumper. The blue cap should pop up and hinge toward the front of the ski exposing the last screw to be removed.
  #17  
Old February 16th 15, 05:40 AM posted to rec.skiing.nordic
[email protected]
external usenet poster
 
Posts: 3
Default How to remove Salomon SNS Profil binding?

On Monday, February 16, 2015 at 12:32:29 AM UTC-5, wrote:
On Monday, February 9, 2009 at 4:07:01 PM UTC-5, jeff potter wrote:
I have a set of skis with the Salomon SNS Profil manual bindings on
them. Skate model.

What's a good way to remove them?

I see what looks like a plug at the rear of the heel plate but they're
not easily removed. I can keep trying.

I've removed the rubber bumpers. The plastic "S" snap-cover in the
front-center of the binding, over the front-center screw, doesn't seem
to want to come off. Do I just work a screwdriver under the front edge
somehow?

How do I expose the 2 side-screws? I don't see how to release the
"bail" so that it can flip out of the way.

Help? Links?

Thanks, JP


This is how I removed my Salomon Profil SNS Alpine cross country ski bindings. I popped off the rear (heel) plastic white cap (3/8" diameter) with a Swiss knife blade and removed the screw below it, I used a number 2 (red) Robertson bit (Canada). Slide the white plate to the rear and off exposing the next screw, remove it and slide off the 2nd white plate to the rear exposing 2 edge (side) screws. Remove them. Next the front (black plastic cap) needs to come off to expose the final screw that holds down the binding for the toe of the boot. Press all the way down on the square release button, hold it down while inserting a flat screwdriver between the black cap and the blue plastic that houses the orange rubber toe bumper. The blue cap should pop up and hinge toward the front of the ski exposing the last screw to be removed.




On Monday, February 16, 2015 at 12:32:29 AM UTC-5, wrote:
On Monday, February 9, 2009 at 4:07:01 PM UTC-5, jeff potter wrote:
I have a set of skis with the Salomon SNS Profil manual bindings on
them. Skate model.

What's a good way to remove them?

I see what looks like a plug at the rear of the heel plate but they're
not easily removed. I can keep trying.

I've removed the rubber bumpers. The plastic "S" snap-cover in the
front-center of the binding, over the front-center screw, doesn't seem
to want to come off. Do I just work a screwdriver under the front edge
somehow?

How do I expose the 2 side-screws? I don't see how to release the
"bail" so that it can flip out of the way.

Help? Links?

Thanks, JP


This is how I removed my Salomon Profil SNS Alpine cross country ski bindings. I popped off the rear (heel) plastic white cap (3/8" diameter) with a Swiss knife blade and removed the screw below it, I used a number 2 (red) Robertson bit (Canada). Slide the white plate to the rear and off exposing the next screw, remove it and slide off the 2nd white plate to the rear exposing 2 edge (side) screws. Remove them. Next the front (black plastic cap) needs to come off to expose the final screw that holds down the binding for the toe of the boot. Press all the way down on the square release button, hold it down while inserting a flat screwdriver between the black cap and the blue plastic that houses the orange rubber toe bumper. The blue cap should pop up and hinge toward the front of the ski exposing the last screw to be removed.


  #18  
Old February 16th 15, 05:41 AM posted to rec.skiing.nordic
[email protected]
external usenet poster
 
Posts: 3
Default How to remove Salomon SNS Profil binding?

On Monday, February 9, 2009 at 4:07:01 PM UTC-5, jeff potter wrote:
I have a set of skis with the Salomon SNS Profil manual bindings on
them. Skate model.

What's a good way to remove them?

I see what looks like a plug at the rear of the heel plate but they're
not easily removed. I can keep trying.

I've removed the rubber bumpers. The plastic "S" snap-cover in the
front-center of the binding, over the front-center screw, doesn't seem
to want to come off. Do I just work a screwdriver under the front edge
somehow?

How do I expose the 2 side-screws? I don't see how to release the
"bail" so that it can flip out of the way.

Help? Links?

Thanks, JP


This is how I removed my Salomon Profil SNS Alpine cross country ski bindings. I popped off the rear (heel) plastic white cap (3/8" diameter) with a Swiss knife blade and removed the screw below it, I used a number 2 (red) Robertson bit (Canada). Slide the white plate to the rear and off exposing the next screw, remove it and slide off the 2nd white plate to the rear exposing 2 edge (side) screws. Remove them. Next the front (black plastic cap) needs to come off to expose the final screw that holds down the binding for the toe of the boot. Press all the way down on the square release button, hold it down while inserting a flat screwdriver between the black cap and the blue plastic that houses the orange rubber toe bumper. The blue cap should pop up and hinge toward the front of the ski exposing the last screw to be removed.
  #19  
Old November 27th 15, 10:24 PM posted to rec.skiing.nordic
[email protected]
external usenet poster
 
Posts: 3
Default How to remove Salomon SNS Profil binding?

best is this video: https://www.youtube.com/watch?v=hLI1RwpBz2s
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
replacing rubber plug for Solomon Profil binding mike Nordic Skiing 6 December 25th 07 01:29 PM
Using Salomon Pilot 2 Classic Boots With Older Profil Classic Binding. ADK Skier Nordic Skiing 7 November 8th 06 09:45 PM
HELP: Profil binding dias-assembly Tony Curran Nordic Skiing 5 November 29th 05 01:39 AM
a profil binding question pls. [email protected] Nordic Skiing 0 November 14th 05 07:55 PM
removing rear fastener on sns profil binding Chris Crawford Nordic Skiing 3 February 26th 05 01:29 AM


All times are GMT. The time now is 08:14 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 SkiBanter.
The comments are property of their posters.