If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Forward Lean Angles
I am planning on playing around with my forward lean angles more this year.
Just for fun, what is everyone setting them up as? I am currently running at 5 degrees from vertical. BTW- Free ride get down the mountain only, love trees/glades no park/pipe. Thanks, Tim |
Ads |
#2
|
|||
|
|||
tg wrote: I am planning on playing around with my forward lean angles more this year. Just for fun, what is everyone setting them up as? I am currently running at 5 degrees from vertical. BTW- Free ride get down the mountain only, love trees/glades no park/pipe. Thanks, Tim More forward lean gives you quicker, more powerful heelsides. Too much forward lean will cause the highback to dig into your calves, forcing you to ride with bent knees all the time... while that's good in terms of technique, it will tire you out quickly (quad burn) and it's not worth it for most people (maybe if you were doing boardercross). I usually ride my bindings with the forward lean either at the maximum lean setting, or one notch back. I have small calves though (and hence require more forward lean). I suggest just setting the forward lean to the highest setting, and then slowly ease it back to a setting that is comfortable to ride in. Don't forget to rotate your highbacks so they are in line with the axis of the board. |
#3
|
|||
|
|||
tg wrote:
I am planning on playing around with my forward lean angles more this year. Just for fun, what is everyone setting them up as? I am currently running at 5 degrees from vertical. BTW- Free ride get down the mountain only, love trees/glades no park/pipe. Thanks, Tim More forward lean gives you quicker, more powerful heelsides. Too much forward lean will cause the highback to dig into your calves, forcing you to ride with bent knees all the time... while that's good in terms of technique, it will tire you out quickly (quad burn) and it's not worth it for most people (maybe if you were doing boardercross). I usually ride my bindings with the forward lean either at the maximum lean setting, or one notch back. I have small calves though (and hence require more forward lean). I suggest just setting the forward lean to the highest setting, and then slowly ease it back to a setting that is comfortable to ride in. Don't forget to rotate your highbacks so they are in line with the axis of the board. |
#4
|
|||
|
|||
lonerider makes the point:
" Don't forget to rotate your highbacks so they are in line with the axis of the board." can you expound upon this? rotate them how? -- jmed |
#5
|
|||
|
|||
lonerider wrote:
[snip text of double post] So Arvin, using Google Groups Beta? Tons of double posts on usenet today because of that POS. As for forward lean, I like "3" on my Raichles. Neil |
#6
|
|||
|
|||
"Jason Medeiros" wrote in message ... lonerider makes the point: " Don't forget to rotate your highbacks so they are in line with the axis of the board." can you expound upon this? rotate them how? Some highbacks can be mounted in one of 3 holes on each side of the binding. If you run with higher angles, then the highback is not parallel to the heelside edge of the board if you do not rotate it. Assuming a binding has holes numbered 1,2,3 on the left and right you may run the highback in pairs (1,1), (2,2), (3,3) if you run 0 or very low binding angles. The highback will be parallel to the heelside of the board. If you run intermediate binding angles you may want to go to pairs of (1,2) or (2,3) ((depending upon angles and front/rear). For higher angles you could go to (1-3). Hope that makes sense. Basically it is an attempt to keep the highback parallel to the heel edge of the board to optimize leverage on the edge. |
#7
|
|||
|
|||
"Neil Gendzwill" wrote in message ... lonerider wrote: [snip text of double post] So Arvin, using Google Groups Beta? Tons of double posts on usenet today because of that POS. As for forward lean, I like "3" on my Raichles. Neil Interesting, does anyone actually measure what that setting is as far as degrees from horizontal or vertical? I know my flows don't have a setting, just the microadjustment with bars, but the angle is dependent upon which slot the cable is in. Seems like it would be nice to know as an absolute for recreating setups etc.... - sorry engineer techo geek coming out in me. |
#8
|
|||
|
|||
Interesting, does anyone actually measure what that setting is as far as
degrees from horizontal or vertical? I know my flows don't have a setting, just the microadjustment with bars, but the angle is dependent upon which slot the cable is in. Seems like it would be nice to know as an absolute for recreating setups etc.... - sorry engineer techo geek coming out in me. Nothing wrong with that. My Salomon Sp6's from a few years back have a fwd lean control that is marked in 3 degree increments up to 27 degrees. |
#9
|
|||
|
|||
What do you have them set to?
21 on the front and 24 on the back for most conditions; less in powder, I think 18 on both. 15 is the minimum setting; measurement is from vertical. I used to ride w/ 27 on both, but since I started hardbooting more, I've been able to carve in softies better without such extreme forward lean. Mike T |
#10
|
|||
|
|||
Ahh... duh... I didn't realize the numbers on my new Catek Freeride /
Salomon SP6 combo. So yea, max forward lean minus one notch is 24 on both... Alas, I am bound to Google Groups for now as I don't have a newsgroup server I can log into to anymore (are their free open ones around?) --Arvin Mike T wrote: What do you have them set to? 21 on the front and 24 on the back for most conditions; less in powder, I think 18 on both. 15 is the minimum setting; measurement is from vertical. I used to ride w/ 27 on both, but since I started hardbooting more, I've been able to carve in softies better without such extreme forward lean. Mike T |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Freeman's forward foot thrust during double poling. | Douglas Diehl | Nordic Skiing | 9 | August 11th 04 03:09 PM |
Stance angles | Dean | Snowboarding | 0 | March 15th 04 10:07 AM |
Going in Circles- The Forward Step In Skating. | Douglas Diehl | Nordic Skiing | 15 | January 13th 04 10:00 PM |
Flow Forward Lean... | toddjb | Snowboarding | 8 | December 25th 03 03:32 PM |
Forward Lean Question - w/ new Ride bindings | toddjb | Snowboarding | 5 | December 9th 03 03:36 PM |