If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Binding Remounting question?
Hi Group,
I bought a used pair of bandit x skis that have a binding on them (marker 1200 piston something) and i want to put my Rossi (Look) binding on them instead. How many times can you remount bindings on a ski? what happens to the holes in the ski from the first binding mount? Looking for info. thanks for the help regards Paul |
Ads |
#2
|
|||
|
|||
Binding Remounting question?
New One wrote:
I bought a used pair of bandit x skis that have a binding on them (marker 1200 piston something) and i want to put my Rossi (Look) binding on them instead. Why go to all that trouble to mount a lesser performing binding? The Marker 1200 piston is no slouch, you know. I'd leave things as they are, have the bindings adjusted and tested by a qualified shop, and just go skiing. How many times can you remount bindings on a ski? Until there are so many holes that the ski is so weak that it breaks. Assuming that the holes are not too close together you can put in a lot of holes before really weakening the ski. I wouldn't start to worry until you need both hands to count the remounts. what happens to the holes in the ski from the first binding mount? Ideally they get filled in with appropriate material (i.e. epoxy) to keep moisture out of the core. If that's not done right, one remounting is too many. Looking for info. Don't do it yourself. Take it to a qualified technician. -- //-Walt // // Sigs suck. Oh, the irony. |
#3
|
|||
|
|||
Binding Remounting question?
Walt wrote:
New One wrote: I bought a used pair of bandit x skis that have a binding on them (marker 1200 piston something) and i want to put my Rossi (Look) binding on them instead. Why go to all that trouble to mount a lesser performing binding? The Marker 1200 piston is no slouch, you know. I'd leave things as they are, have the bindings adjusted and tested by a qualified shop, and just go skiing. One possible valid reason would be if the current bindings have to be remounted to fit a different boot sole length; then the new holes might be too close to the old holes, weakening the skis. In that case a different binding with different hole patterns might be the way to go. However, you are correct; the best solution would be if the current bindings can be adjusted. Any decent skier can adapt to being a cm or so fore or aft of the factory indicated position on the skis. I agree on the bindings - IMO the Markers would be preferred to the Rossis all else being equal. |
#4
|
|||
|
|||
Binding Remounting question?
Thanks you both for the info. exactly what i needed. Only thing is, why do
you guys feel the marker (1200) is a better binding than the rossi/look p10? I am an expert skier on bumps and crud. will i be able to tell a difference between the two immediately? thanks Paul "lal_truckee" wrote in message ... Walt wrote: New One wrote: I bought a used pair of bandit x skis that have a binding on them (marker 1200 piston something) and i want to put my Rossi (Look) binding on them instead. Why go to all that trouble to mount a lesser performing binding? The Marker 1200 piston is no slouch, you know. I'd leave things as they are, have the bindings adjusted and tested by a qualified shop, and just go skiing. One possible valid reason would be if the current bindings have to be remounted to fit a different boot sole length; then the new holes might be too close to the old holes, weakening the skis. In that case a different binding with different hole patterns might be the way to go. However, you are correct; the best solution would be if the current bindings can be adjusted. Any decent skier can adapt to being a cm or so fore or aft of the factory indicated position on the skis. I agree on the bindings - IMO the Markers would be preferred to the Rossis all else being equal. |
#5
|
|||
|
|||
Binding Remounting question?
New One wrote:
Thanks you both for the info. exactly what i needed. Only thing is, why do you guys feel the marker (1200) is a better binding than the rossi/look p10? In testing over the years Marker has shown the most consistent predictable release characticistics. This is due mainly to their cam-based release mechanism as opposed to the spring-based release mechanism you see on other brands. Marker also has the best Anti-Friction device going. Note that this is somewhat of a religious issue and that others will differ. I am an expert skier on bumps and crud. will i be able to tell a difference between the two immediately? Probably not. Which is why I'd leave the Markers. BTW, for all my pro-Marker rantings, the newest addition to the quiver has Look p10 bindings on them. The jury is still out since I haven't managed to pop a binding yet. -- //-Walt // // Sigs suck. Oh, the irony. |
#6
|
|||
|
|||
Binding Remounting question?
New One wrote:
Thanks you both for the info. exactly what i needed. Only thing is, why do you guys feel the marker (1200) is a better binding than the rossi/look p10? I am an expert skier on bumps and crud. will i be able to tell a difference between the two immediately? Maybe, maybe not. The Look turntables traditionally had more "return to center" so you could start to release and if the force was removed the binding would pull the boot back to position; Markers traditionally retained you locked in position untill release force was exceeded and bingo you were out - no "return to center" at all. Current Look turntables have a different toe and I haven't skied the new version, so I don't know if it's still true for today's version. Another difference was the Look shorter turntable mounting allowed rounder ski flex; I don't know if you will feel that, or even like it if you did feel it - some do some don't. A third difference isn't immediate - old Markers lasted longer and broke less than old Looks (although I had only a couple of Look TT failures in many years of Look TT skiing.) It might still be true but we won't know for years. Also I think the P10 is Din 3-10 and the 1200 is Din 3-12; probably you will not ski at the higher Din, unless you get on extreme steeps where release cannot be allowed or you race, so it probably won't matter. All my current skis are mounted with Markers: except for Fritschi Freerides on the backcountry skis, and Salomons on both pairs of DH racing skis. Occasionally I take out a semi-retired pair still mounted with old style Look turntables. thanks Paul "lal_truckee" wrote in message ... Walt wrote: New One wrote: I bought a used pair of bandit x skis that have a binding on them (marker 1200 piston something) and i want to put my Rossi (Look) binding on them instead. Why go to all that trouble to mount a lesser performing binding? The Marker 1200 piston is no slouch, you know. I'd leave things as they are, have the bindings adjusted and tested by a qualified shop, and just go skiing. One possible valid reason would be if the current bindings have to be remounted to fit a different boot sole length; then the new holes might be too close to the old holes, weakening the skis. In that case a different binding with different hole patterns might be the way to go. However, you are correct; the best solution would be if the current bindings can be adjusted. Any decent skier can adapt to being a cm or so fore or aft of the factory indicated position on the skis. I agree on the bindings - IMO the Markers would be preferred to the Rossis all else being equal. |
#7
|
|||
|
|||
Binding Remounting question?
Walt wrote:
New One wrote: Thanks you both for the info. exactly what i needed. Only thing is, why do you guys feel the marker (1200) is a better binding than the rossi/look p10? In testing over the years Marker has shown the most consistent predictable release characticistics. This is due mainly to their cam-based release mechanism as opposed to the spring-based release mechanism you see on other brands. Marker also has the best Anti-Friction device going. Note that this is somewhat of a religious issue and that others will differ. I am an expert skier on bumps and crud. will i be able to tell a difference between the two immediately? Probably not. Which is why I'd leave the Markers. BTW, for all my pro-Marker rantings, the newest addition to the quiver has Look p10 bindings on them. The jury is still out since I haven't managed to pop a binding yet. You are drummed out of the club; badges of honor ripped from your heaving chest; you're ski bases are gouged by burning brands; and all your mates have turned their backs on you. But really, no one cares ... |
#8
|
|||
|
|||
Binding Remounting question?
lal_truckee wrote:
Walt wrote: BTW, for all my pro-Marker rantings, the newest addition to the quiver has Look p10 bindings on them. The jury is still out since I haven't managed to pop a binding yet. You are drummed out of the club; badges of honor ripped from your heaving chest; you're ski bases are gouged by burning brands; and all your mates have turned their backs on you. But really, no one cares ... Fortunately, I don't look anything like Chuck Conners. -- //-Walt // // There's a village in Texas that's missing its idiot. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Used ski advice, ski binding question | Patrick G. Bridges | Alpine Skiing | 0 | March 10th 04 10:04 AM |
Newbie Binding Setup Question | Joe Blanchard | Snowboarding | 2 | February 26th 04 07:57 PM |
Binding Question | Wes Gardner | Alpine Skiing | 1 | February 22nd 04 07:42 PM |
Binding Question | Wes Gardner | General | 0 | February 22nd 04 01:45 PM |
Pilot binding system -- what's the point? | Ken Roberts | Nordic Skiing | 1 | August 14th 03 03:28 PM |