If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Fixing high spots in ski base
After skiing on an icy track I noticed that the wax had worn off my
bases quite differently on the two skis. On one ski there was a 6" white area about 2'in front of the binding, while on the other ski there was similar wear spot about 1' behind the back of the binding. Obviously these are high spots that need to be removed. The ski has been stone ground, and I'm told that that procedure does not address this kind of issue. How does one go about removing places that are pressure points on the bases of skis? Is there a website that describes the procedure? -Everett |
Ads |
#2
|
|||
|
|||
Is white base after skiing all the evidence you have for these being high spots? How do you know the bases are just not absorbing wax in these areas? -Mitch On Thu, 18 Nov 2004, Everett Fee wrote: After skiing on an icy track I noticed that the wax had worn off my bases quite differently on the two skis. On one ski there was a 6" white area about 2'in front of the binding, while on the other ski there was similar wear spot about 1' behind the back of the binding. Obviously these are high spots that need to be removed. The ski has been stone ground, and I'm told that that procedure does not address this kind of issue. How does one go about removing places that are pressure points on the bases of skis? Is there a website that describes the procedure? -Everett |
#3
|
|||
|
|||
Everett,
Is there any chance these two spots could have been overheated with a waxing iron? And therefore many of the pores in these areas of the base are melted closed - so wax is not being absorbed adequately? If that was the case ... and if the damage is not too deep, the skis could be re-ground to remove these "burnt" spots. TK |
#4
|
|||
|
|||
Rather than being high spots these could be places where the base has
been damaged/sealed by using a too hot iron during waxes. Or the base could just have come that way. Does anyone know if improper stone grinding technique could cause the base to become sealed? Ralph ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 100,000 Newsgroups ---= East/West-Coast Server Farms - Total Privacy via Encryption =--- |
#5
|
|||
|
|||
There are two likely culprits. First, the base could be burnt or
"sealed" by overheating with an iron or during the stone grind. This seals the pores in the base and prevents wax absorption. You can metal scrape these areas and you will be able to tell if it is burnt by the base being harder in that region than on the rest of the base. If you get after it with the metal scraper, you should be able to get down to fresh base and the spots will go away with some waxing. If it is not a burnt spot, then it is likely that you have "hot spots". This probably has less to do with a high spot on the base and more to do with the flex of the ski. There is not much you can do about that. -Nathan www.nsavage.com "Everett Fee" wrote in message m... After skiing on an icy track I noticed that the wax had worn off my bases quite differently on the two skis. On one ski there was a 6" white area about 2'in front of the binding, while on the other ski there was similar wear spot about 1' behind the back of the binding. Obviously these are high spots that need to be removed. The ski has been stone ground, and I'm told that that procedure does not address this kind of issue. How does one go about removing places that are pressure points on the bases of skis? Is there a website that describes the procedure? -Everett |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
FA: ADIRONDACK MOUNTAIN CLUB Annual~1940 "High Spots" vintage copy | [email protected] | Marketplace | 0 | March 5th 04 08:28 AM |
grey areas on base | Griss | Nordic Skiing | 3 | February 7th 04 08:55 PM |
Why wax? | Pertti Ruismäki | Snowboarding | 4 | January 20th 04 04:17 PM |
Base Repair: P-tex or powder ? | Ron N.Y | Alpine Skiing | 5 | January 13th 04 10:33 PM |
wood ski base prep question | Sanjay Arwade | Nordic Skiing | 1 | January 5th 04 10:20 PM |