![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
Hi - I'm replacing a profil binding with a new pilot binding. I've
removed all the old binding except the heel plate which is attached by a small yellow plug in at the rear of the heel plate. All adhesive has been pried free so the heel plate is rotating about this plug. The profil binding is a grey model about 2 years old. The little yellow plastic plug has a slight flat head screw slot in the top but I'm pretty sure this is not for unscrewing. My recollection is that this is a little expander plastic plug that I pushed down into a hole in the ski but I really can't remember. How can I remove it? Pry the heel plate off until it breaks? Drill it out? Is this a replaceable part I can find if I want to re-use the binding? Thanks for your help!! Regards Chris |
Ads |
#2
|
|||
|
|||
![]() "Chris Crawford" wrote: Hi - I'm replacing a profil binding with a new pilot binding. I've removed all the old binding except the heel plate which is attached by a small yellow plug in at the rear of the heel plate. All adhesive has been pried free so the heel plate is rotating about this plug. The profil binding is a grey model about 2 years old. The little yellow plastic plug has a slight flat head screw slot in the top but I'm pretty sure this is not for unscrewing. The plug is just pressed in. You can gently pry the plug off by sticking a sharp tipped knife a bit into the seam and gently prying up on the side of the plug, working around the button. Be careful not to break your knife tip though! Use a thin knife. It's just pressed in. If you can't manage that, stab the tip of a screwdriver through the "slight flat head screw slot" of the plug and pry it off that way. Once the plug is off, you'll see the screw underneath. |
#3
|
|||
|
|||
![]()
In article .com,
"Chris Crawford" wrote: Hi - I'm replacing a profil binding with a new pilot binding. I've removed all the old binding except the heel plate which is attached by a small yellow plug in at the rear of the heel plate. All adhesive has been pried free so the heel plate is rotating about this plug. The profil binding is a grey model about 2 years old. The little yellow plastic plug has a slight flat head screw slot in the top but I'm pretty sure this is not for unscrewing. My recollection is that this is a little expander plastic plug that I pushed down into a hole in the ski but I really can't remember. How can I remove it? Pry the heel plate off until it breaks? Drill it out? Is this a replaceable part I can find if I want to re-use the binding? Thanks for your help!! Regards Chris Older SNS bindings have a plastic pin that seats in the heel plate and goes into the hole drilled in the ski. The pin has "ribs" on its shaft to help keep it in the ski and prevent the heel plate from loosening. If your binding has this pin then you can remove it by prying the heel around the pin with a putty knife until the pin pops out. Another alternative is to simply drill the pin out. If you need to reuse the heel plate you can use a screw instead of the pin. New SNS Profil bindings have a screw holding the heel plate down. The screw seats deeply into the heel plate and the top of the screw is hidden by a plastic plug. To remove the plug you can do as Andrew Lee suggests. Another way to remove it is to use a sharp pointed tool like an awl or ice pic and punch a small hole into the plug. You can then use the tool to pry out the plug. You can still use the plug with the hole in it but I suggest sealing the hole with a little glue to keep water (melted snow) from getting into the screw area. When doing all this mucking around with the heel plate, especially if you are removing the plastic pin, you might just enlarge the hole in the ski si that when affixing the new binding the screw does not tighten. A good way to "fix" this problem is to epoxy a golf tee tightly in the hole then cut it off flush with the top of the ski. Let the epoxy harden firmly then drill a new hole in the golf tee to accept the binding screw. Ralph Thornton http://www.ernordic.com/ralph.htm |
#4
|
|||
|
|||
![]() Quote:
Thanks (in advance). |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Pilot binding system -- what's the point? | Ken Roberts | Nordic Skiing | 1 | August 14th 03 03:28 PM |