If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#91
|
|||
|
|||
why hardboots?
"Mike T" wrote in message ...
Interesting, whay size feet and whawt width board to you ride? Obviously I'm still playing with my stance setup. Mondo 28, on a 19.5 cm wide board. Those angles give me a couple of mm overhang on the rear foot, and a couple of mm underhang on the front foot. Just another data point: Raichle shell, Mondo 25, Catek or TD2 step-in bindings, ~19" wide stance 18 cm waist - 57 back foot is flush with edge 18.5 waist - 55 back foot is flush (bigger sidecut than above board, means less widening as you go out from waist) 21.5 waist - pretty much any alpine stance will underhang a bit Mike T How do you compute over/underhang? I'm riding a Mondo 25.5 Oxygen Protons, which actually have soles that are a couple of mm longer than my 26 Raichle 224s. The Prior 4WD had a 21.3 waist, 9.5 m sidecut and it looks like I had 0 overhand (looking straight down) with 53/48. My Burton Ultraprime 162 has like a 20 cm (roughly) waist. How much does a wide board make a difference? Like is a 19 cm board much quick edge to edge than a 21 cm board? |
Ads |
#92
|
|||
|
|||
why hardboots?
On 22 Mar 2004 00:18:14 -0800, Arvin Chang said (and I quote):
How do you compute over/underhang? I'm riding a Mondo 25.5 Oxygen Protons, which actually have soles that are a couple of mm longer than my 26 Raichle 224s. I don't really *compute* it. I just click my boots into the bindings, and then hold the board perpendicular to the ground, and then try to put a ruler at 90 deg to the edge. How much does a wide board make a difference? Like is a 19 cm board much quick edge to edge than a 21 cm board? I don't think the edge-to-edge issue is that important. Better to figure out the stance angles you like, and then get a board the right width for them. Alternatively, if you want to ride powder you have to figure that into it. -- A: Top-posters. Q: What's the most annoying thing on usenet? |
#93
|
|||
|
|||
why hardboots?
How do you compute over/underhang? I'm riding a Mondo 25.5 Oxygen
Protons, which actually have soles that are a couple of mm longer than my 26 Raichle 224s. I don't really *compute* it. I just click my boots into the bindings, and then hold the board perpendicular to the ground, and then try to put a ruler at 90 deg to the edge. Same here - not computing at all. I just mount the bidning but the top plate loose, put the boot in the binding and rotate the top plate until the boot is flush with the edge. I do this with the board leaned against the wall at an angle, boot facing inward, so I'm looking at the base.... and find the lowest angle such that you can't see any boot or binding when looking at the base. Close enough for gov't work. This is how I choose the "starting out" stance on a new board... set the back binding up so its flush and then add another 3 - 5 degrees to the front. How much does a wide board make a difference? Like is a 19 cm board much quick edge to edge than a 21 cm board? I don't think the edge-to-edge issue is that important. Better to figure out the stance angles you like, and then get a board the right width for them. Alternatively, if you want to ride powder you have to figure that into it. Works best if you have a demo tent at your disposal Ideally I'd have alpine boards with a few different waist widths for different types of snow. On hardpack I prefer an 18 cm waist because edge-to-edge response is noticeably better and more important to performance. For days when it's snowing in the AM and the groomers have a layer of snow on them (very common at Mt Hood) I like a wider waist and a little boot underhang... this way the board clears a better path for the boots to follow. Same for carving the corn snow. I find I'm comfortable with anything from 54/48 to 66/63... higher being better for aggressive carving due to the fact that higher angles tend to favor heelside which I am weaker at. Mike T |
#94
|
|||
|
|||
why hardboots?
One thing you have to watch for on the heel side is all the gee-gaws
that stick out the back of the boot. I like to put the boot in the binding and then lay the board over 90 degrees to make sure nothing hits, not the heel nor the lean adjustor or whatever. |
#95
|
|||
|
|||
why hardboots?
Just another point of comparison:
I'm in size 27 Raichle/Deeluxe, and on a 24 cm waist board I have probibly 5mm or more of underhang with angles as low as 48. Recently I got to ride a board that was 1.5 cm narrower in the waist than my usual board (this is on softboots) and it felt dramaticly quicker edge to edge. Since then, I've started to think that "edge quickness" has more to do with how much overhang or underhange you have, not the actual width. More clearly: I suspect thata a 21.5 cm freecarve board with a stance that had 0 overhang would feel basicly as fast as a 19 cm race/freecarve board that also had a stance of 0 overhang. Mike: you're probibly the only person I know that rides a few different stances and widths... what do you think? |
#96
|
|||
|
|||
why hardboots?
Baka Dasai wrote in message ...
On 22 Mar 2004 00:18:14 -0800, Arvin Chang said (and I quote): How do you compute over/underhang? I'm riding a Mondo 25.5 Oxygen Protons, which actually have soles that are a couple of mm longer than my 26 Raichle 224s. I don't really *compute* it. I just click my boots into the bindings, and then hold the board perpendicular to the ground, and then try to put a ruler at 90 deg to the edge. I meant to say what are you measuing from, with my low angles I see a tiny bit overhang on the other toe bail of my bindings, but my boots are pretty much inside the board profile (this is with a 21.3 cm board). How much does a wide board make a difference? Like is a 19 cm board much quick edge to edge than a 21 cm board? I don't think the edge-to-edge issue is that important. Better to figure out the stance angles you like, and then get a board the right width for them. Alternatively, if you want to ride powder you have to figure that into it. I see, I felt with the Prior 4WD board that it seems like I had to angulate a lot before the board started to really come up on edge, even compared to the Burton UP, which is only 1 cm narrower. |
#97
|
|||
|
|||
why hardboots?
While we're on the subjet of hard boots, www.bomberonline.com has their
boots on sale right now. The best deals IMHO a Raichle SB 423 - $150 Raichle SB 413 - $125 Limited sizes are available Even with all the criticisms of Raichle boots listed here, IMHO either of these makes a great first pair of hard boots especially at these prices. The 423s come with a Thermoflex liner. As Arvin, myself, and others have found out, sizing hard boots can be tricky. Everyone says "measure your foot in cm and order your measurement in Mondo Point size" but for many of us that gives you a boot that's too big. Example: My feet measue about 26.5 cm in length but I use a 26 Salomon Malamute soft boot - and a 25 Raichle SB series shell. I rode for two years on 26 Raichle shells until I realized they were too big! Bomber is really good about returns if you follow the rules - try them on in the house. If you think you're in between two sizes you can order both and then return the one that doesn't fit as well, they're used to people doing that. -Mike T Disclaimer: I don't work for Bomber, I'm just a very satisfied customer of theirs. |
#98
|
|||
|
|||
why hardboots?
Recently I got to ride a board that was 1.5 cm narrower in the waist
than my usual board (this is on softboots) and it felt dramaticly quicker edge to edge. Since then, I've started to think that "edge quickness" has more to do with how much overhang or underhange you have, not the actual width. More clearly: I suspect thata a 21.5 cm freecarve board with a stance that had 0 overhang would feel basicly as fast as a 19 cm race/freecarve board that also had a stance of 0 overhang. Mike: you're probibly the only person I know that rides a few different stances and widths... what do you think? I think it's a little more complicated than that unfortunately. First of all there are factors other than waist width and overhang, underhang or lack thereof. Torsional stiffness is a big factor. A board that is more torsionally stiff will change edges faster than one that is less torsionally stiff. Also keep in mind that going from, using Jason's example, 21.5 cm to 19 cm, keeping your boots flush with the edges requires a pretty radical change in stance. Most of us won't be able to ride equally well in both stances. When I'm on my Axis (21.5 cm) I ride with probably 5 - 10 mm of underhang, because the loss in edge change speed (which is noticeable BTW) is more than made up for in comfort and the ability to apply my "normal" alpine technique at the higher angles. (Although Jason would probably say that I still look a lot better on my Coiler at even higher stance angles.) So that's about all I can say from personal experience... I suspect the more advanced folks over at Bomber would be able to pick this argument apart and get to the bottom of it. FWIW, I can say that a Donek FC 163 at 18 cm waist changes edges noticeably faster than a Coiler PR 184 at 18.5 cm. Much more than one would expect given the tiny 5mm difference in waist width. The Donek is noticeably torsionally stiffer. Edge change speed isn't the end all, be all of alpine riding though... it's only one part. On that Donek I found that edge changes happened without thinking about it, but holding the edge through the turn took some focus. On the Coiler edge changes take a little focus, but holding the edge through the turn just happens. I don't know how much of that is due to who made the boards and how much is due to them being different lengths and sidecut though - hopefully I'll try other peoples' boards and find out some day! Mike T |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Beginner - Starting off with soft boots? | Guy Lux | Snowboarding | 7 | January 22nd 04 07:45 PM |
difference between hard and soft boots | Brendon | Snowboarding | 11 | September 17th 03 08:27 AM |